Hook up ice maker refrigerator
Keep an extra 8 to 10 feet of water tubing rolled up neatly behind the refrigerator to allow enough tubing to be pulled out if you have to slide the refrigerator away from the wall. Whenever drilling holes for water lines, always be sure to use a paddle bit that's one to two sizes larger than the water supply line to prevent the line from kinking. To tap into the line, shut off the water to the house at the main.
Plumb the fridge
Attach a water valve to the T-fitting. Tighten up the mounting screws to secure the unit to the freezer wall, and then add the ice bucket under the kit. How to Paint Laminate Kitchen Countertops.
Reader's Digest Taste of Home Recipes. Finally, drain the lines by opening a faucet. Locate the cold water source closest to the refrigerator.
Articles lacking sources from December All articles lacking sources Orphaned articles from December All orphaned articles. Home Guides Home Home Improvement. This will flush the gunk from the tube into the bucket.
Using the plastic tubing provided with the kit, screw the plastic fitting to the water outlet on the bottom of the solenoid valve. Mount the unit to the freezer wall by hanging the icemaker hook up ice maker refrigerator the mounted screws; making sure to line up the extension dating or hooking up into the reservoir.
You can replace the auger motor without reconnecting it if you intend on installing a new ice maker in the future.
Tapping the Cold Water Line
Twist the male end of a quick-tee adapter onto the valve. To straighten coiled tubing not the entire rollhave a partner hold the end of the tube flat on the floor, then push the roll against the floor while unrolling to the length you need just hook up calgary go through the cabinets. Warnings Make sure your refrigerator is disconnected before attaching the water supply line.
Plug your refrigerator into the wall. Mount the Unit to the Freezer Wall Mount the unit to the freezer wall by hanging the icemaker over the mounted screws; making sure to line up the extension tube into the reservoir.
Required Tools for this Project
Unsourced material may be challenged and removed. Notify me of new posts by email. This article will show you how to run a water line to your refrigerator for an automatic ice maker and hook up ice maker refrigerator dispenser.
Let 1 or 2 gallons of water run through the new line to remove the air.
Depending on brand of refrigerator, you will need certain types of water filters. Use a flathead screwdriver to remove the plugs from the holes.
Slide the provided water valve clamp over the fill tube, insert the water supply line and use a drill with a hex head bit to tighten everything up. Do not replace the ice bin. Step 6 — Get out the plastic water tubing from your fridge water line kit. Thread copper tubing through the hole you just drilled.
The name is derived from the fact that it is mounted in such a way that it "saddles" the line, mounting it from both sides. Attach one end of the copper tubing to the refrigerator's water pipe, using a nut and ferrule.
If you need to drill through floors or walls, check for air ducts, electrical wiring, plumbing or other possible impediments first. Step 11 — If there are no leaks, plug in your refrigerator and turn the ice maker on.
This extra tubing will allow you to move the refrigerator away from the wall for cleaning and servicing without disconnecting the water supply. If applicable to your refrigerator, run the tubing through the hose clamp to hold it at the preferred angle. Insert the new water line into the opening on the tee.
Drill as close to the back wall of the cabinet as possible, so you do not lose storage space inside the cabinet. Now that the ice maker is completely installed, plug in the refrigerator. Next, tighten down the "T" handle until it's tight and pierces the copper line.
She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction.
Attach the water supply line with the provided compression fitting to the top of the solenoid valve by hook up an amp it into place then tightening it up with a crescent wrench. Turn off the small valve beneath the sink. Finally, turn the water back on at the main and switch the electric water heater breaker back on or turn the gas water heater to the on position.